A failed bearing is a message, not just scrap metal. Where the material went, what colour the race turned, whether the rollers are marked or the raceway is pitted — each of those points to a cause, and the cause decides whether a rebuild will last or fail again within a season. Guangzhou Shenyue Machinery Technology Co., Ltd. supplies bearings into Kobelco travel motors, swing motors and pumps, and the same handful of patterns comes back from workshops year after year.
Photograph it before you clean it
The first minute matters. Photograph the bearing in place, note the oil level and colour, and keep the drained oil. Dark oil with a metallic shimmer tells you the failure has been running for a while. Clean oil and a suddenly noisy unit tells you it happened fast, which usually means a shock load or a lubrication interruption rather than wear.
The four patterns that cover most failures
| Pattern | What you see | Usual cause |
|---|---|---|
| Fatigue spalling | Flaking that starts on the raceway, often with a dull grey halo around it | End of normal life, or overload from a worn mating part |
| Brinelling | Evenly spaced dents in the race, matching the roller spacing | Shock load, hammering during installation, or a unit left standing under load |
| Heat damage | Blue, brown or straw colour; deformed cage | Lubrication loss, wrong oil, or a bearing fitted with too little clearance |
| Abrasive scoring | Fine scratches across race and rollers, a lapped appearance | Contamination through a failed seal, or debris left in the housing |
Most real failures are a combination. Heat damage and scoring usually travel together: the seal lets grit in, the grit polishes the race, friction raises temperature, and the cage gives up. Reading only the final damage leads to replacing the bearing and leaving the seal, which is why the same unit returns.
Where these patterns appear on Kobelco machines
Travel motor bearings usually show fatigue spalling first on the output side, because that is where track load arrives. Swing motor bearings are different in character: the needle and roller bearings inside a swing unit often fail from lubrication starvation rather than load, since the swing case holds a small oil volume and leaks go unnoticed for months. Our records carry LQ15V00008S010 as a swing motor needle bearing and YN15V00002S011 as a swing motor roller bearing — small parts that write off a large assembly when they let go.
Pump bearings fail in their own way. A pump run on aerated oil shows fine scoring long before it shows measurable play, which is why a pump that "suddenly" seized usually had a suction leak for weeks.
One bearing, three numbers
Quoting bearings is where buyers lose time. A single physical bearing can be listed under a manufacturer number, a Kobelco group number and an internal code. Our records show PNUP309ET, 2441U474S123 and 2437U534S123 as one and the same bearing, and PNJ309ET with LB15V00011S443 as another. C6258317548601 and 2441U1040S32 pair in the same way, while C22783175626N1 stands alone. Send whichever number is stamped on the old part together with the machine model; a supplier who accepts only one format will eventually quote the wrong bearing with complete confidence.
Rebuild or replace: the bench decision
A rebuild is worth doing when the housing bore is round, the shaft journal is within tolerance and the damage is confined to the bearing. It is not worth doing when heat has discoloured the housing, when the shaft is worn under the inner ring, or when metal from the failed bearing has travelled through the unit. In those cases the honest answer is a complete assembly or a good used unit, and the decision belongs on the bench with a micrometer. Guangzhou Shenyue Machinery Technology Co., Ltd. will give the same answer either way, because a bearing sold into a damaged housing comes back.
Fitting rules that stop a repeat failure
Never drive a bearing home through the rollers. Heat it only if the manual says to, press on the ring that carries the interference, and check axial play after assembly rather than before. Keep the housing covered while the unit is open — most abrasive scoring we are asked about started as a workshop rag that was not clean.
Replace the seals with the bearing, every time. A new bearing behind a leaking seal will be back on the bench within a season, and the second failure usually takes the shaft with it — the seal material guidance published by NOK explains how much of that depends on the oil and the temperature the unit actually sees. If the unit is already apart, the bearing catalogue listing and the travel motor internal parts guide will help you match what came out; hydraulic assemblies are grouped under hydraulic components. When the pattern is unclear, send us the photos before ordering anything.
Frequently Asked Questions
What does brinelling look like and what causes it?
Brinelling shows as evenly spaced dents in the raceway, matching the roller spacing, with no flaking yet. It comes from shock load or from hammering a bearing into place. Guangzhou Shenyue Machinery Technology Co., Ltd. sees it most on travel motors that have been dropped or fitted with a hammer rather than a press.
My swing motor is noisy but still turns. Can I keep running?
Short term, yes, with monitoring, but noise from a swing unit is usually a bearing or a lubrication problem and both get worse. Our records list LQ15V00008S010 and YN15V00002S011 as swing motor bearings. Continuing to run risks the housing, which turns a bearing job into an assembly replacement.
Why do suppliers quote different numbers for the same bearing?
Because one bearing can carry a manufacturer number, a Kobelco group number and an internal code at the same time. PNUP309ET, 2441U474S123 and 2437U534S123 are the same bearing in our records. Quote the stamped number and the model so the match can be confirmed.
Is a used travel motor a sensible alternative to a rebuild?
Sometimes. A used unit makes sense when the housing is damaged or when downtime matters more than long-term life, provided the donor is tested and the serial is traceable. Guangzhou Shenyue Machinery Technology Co., Ltd. grades used units openly so the buyer knows which one they are getting.